收藏本站
LTM8026
APPLICATIONS INFORMATION
LTM8026s equally sharing output current is shown in the
Typical Applications section. The modulation of the CTL_I
inputs is performed at a high bandwidth, so use an op
amp with a gain bandwidth product greater than 1MHz.
The example circuit in the Typical Applications section
uses the LTC6255, which has a minimum gain bandwidth
product of 2MHz.
?
?
?
?
?
?
?
GND
?
?
?
?
?
?
?
?
SYNC
RUN
C IN
? THERMAL AND INTERCONNECT VIAS
The LTM8026’s CVCC operation provides the ability to
power share the load among several input voltage sources.
An example of this is shown in the Typical Applications
section; please refer to the schematic while reading this
discussion. Suppose the application powers 2.5V at 8A
and the system under consideration has regulated 24V
and 12V input rails available. The power budget for the
power rails says that each can allocate only 750mA to
produce 2.5V. From the Input Current vs Output Current
graph in the Typical Performance Characteristics section
for 2.5V OUT , 750mA from the 24V rail can support more
than 5A output current, so apply a 66.5k/140k from V REF
to the CTL_I pin of the LTM8026 powered from 24V IN to
set the output current to 5A. These resistor values were
derived as follows:
1. The typical output current limit is 5.6A for CTL_I = 1.5V
and above.
2. To get 5A, make the voltage on CTL_I = 1.5V ? 5 A/5.6A
= 1.34V.
3. The V REF node is a regulated 2V, so applying the
66.5k/140k network yields 2V ? 140 k/(66.5k + 140k) =
1.35V
The LTM8026 powered from 12V IN needs to supply the
rest of the load current, or 3A. Again referring to the Input
Current vs Output Current graph in the Typical Performance
Characteristics section for 2.5V OUT , 750mA will support
more than 3A when operated from 12V IN . Using a method
similar to the above, apply a resistor network of 132k/78.7k
to the CTL_I pin:
1. To get 2.5A, make the voltage on CTL_I = 1.5V ? 3 A/5.6A
= 0.8V
C OUT ? ? ?
? ? ? ? ? ? ?
? ? ? ? ? ?
? ? ? ? ? ? ?
V OUT V IN
GND V OUT
GND V IN
8026 F05
Figure 5. Layout Showing Suggested External Components, GND
Plane and Thermal Vias.
As seen in the graph accompanying the schematic in the
Typical Applications section, the input currents to each
LTM8026 stays below 750mA for all loads below 8A.
PCB Layout
Most of the headaches associated with PCB layout have
been alleviated or even eliminated by the high level of
integration of the LTM8026. The LTM8026 is neverthe-
less a switching power supply, and care must be taken to
minimize EMI and ensure proper operation. Even with the
high level of integration, you may fail to achieve specified
operation with a haphazard or poor layout. See Figure 5
for a suggested layout. Ensure that the grounding and
heat sinking are acceptable.
A few rules to keep in mind are:
1. Place the R ADJ and R T resistors as close as possible to
their respective pins.
2. Place the C IN capacitor as close as possible to the V IN
and GND connection of the LTM8026.
2. Applying a 132k/88.7k network to V REF and CTL_I yields
2V ? 88.7 k/(88.7k + 132k) = 0.8V
8026fb
For more information www.linear.com/LTM8026
17
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LTM8027EV#PBF IC BUCK SYNC ADJ 4A 113LGA
LTM8032MPY#PBF IC DC/DC UMODULE 2A 71BGA
LTM8033MPV#PBF IC DC-DC UMODULE BUCK 3A 76-LGA
LTM8040IV#PBF IC LED DRVR HP CONST CURR 66-LGA
LTM8042IV#PBF IC UMODULE LED DRIVER 56LGA
LTM8048MPY#PBF IC DC/DC UMODULE LDO BGA
LTM8052AEV#PBF IC UMODULE 36VIN 5A CVCC 81LGA
M30R224K5 CAP CER 0.22UF 50V 10% RADIAL
相关代理商/技术参数
LTM8027 制造商:LINER 制造商全称:Linear Technology 功能描述:60V、4A DC/DC μModule 穩壓器
LTM8027EV 制造商:LINER 制造商全称:Linear Technology 功能描述:60V, 4A DC/DC Module Regulator
LTM8027EV#PBF 功能描述:IC BUCK SYNC ADJ 4A 113LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:*
LTM8027EV#PBF 制造商:Linear Technology 功能描述:DC/DC Converter IC 制造商:Linear Technology 功能描述:IC, STEP-DOWN DC/DC MODULE REG, LGA-113
LTM8027EVPBF 制造商:Linear Technology 功能描述:DC/DC Regulator 4A 60Vin 2.5-24Vout
LTM8027IV 制造商:LINER 制造商全称:Linear Technology 功能描述:60V, 4A DC/DC Module Regulator
LTM8027IV#PBF 功能描述:IC BUCK SYNC ADJ 4A 113LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:21V 电压 - 输入（最大）:32V Voltage - Output 1:5V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:*
LTM8027IV#PBF 制造商:Linear Technology 功能描述:DC/DC Converter IC